School Physics Laboratory table Furniture

A durable laboratory workstation featuring a dark green corrosion-resistant worktop, integrated stainless steel utility fixtures (gas taps, electrical outlets, and sink with a tall gooseneck faucet), and seamless white storage cabinets below. Designed for educational and research labs, it supports hands‑on experiments with ergonomic accessibility and easy‑clean surfaces.

Product Description

1. New type of plastic-aluminum structure, overall size 1200*600*760mm. The student workstations are hollowed out, conforming to ergonomic design, simple and beautiful, with rounded corners at all easily impacted areas.

2. The tabletop uses 12.7mm thick double-sided film solid core phenolic resin board, and meets the following parameter requirements:

★(1) Chemical performance testing: According to GB/T 17657-2022 “Test Methods for Physical and Chemical Properties of Wood-based Panels and Decorative Wood-based Panels”, the stain resistance performance is tested for no less than 130 pollutants, including: 65% nitric acid, 98% sulfuric acid, potassium hydroxide, liquid bromine, ammonium acetate, butyl acetate, citric acid, mercurochrome, methyl orange, m-xylene, turpentine, etc. The test results for both covered and uncovered glass covers are level 5: no significant change. ★(2) Physical performance testing: Based on GB/T 17657-2022 “Test Methods for Physical and Chemical Properties of Wood-based Panels and Decorative Wood-based Panels”, the following tests were conducted: Moisture content: ≤0.9%; Water absorption thickness expansion rate: ≤0.1%; Dimensional stability: Transverse ≤0.07%, Longitudinal ≤0.04%; Screw holding force ≥3490N; Surface resistance to thermal cycling: No cracks or blistering on the surface; Impregnation peeling performance: No peeling or delamination of the adhesive layer between the veneer and the substrate; Surface scratch resistance: No continuous scratches exceeding 90% on the surface of the specimen under 4.5N, and no damage to the decorative patterns on the surface; Boiling water resistance: Mass increase percentage ≤0.01%, thickness increase percentage ≤0.08%, Surface quality grade: Grade 5: No change, Edge quality grade: Grade 5: No significant change; Crack resistance: Grade 5: No micro-cracks; Surface abrasion resistance: ≥1100r, no wear points, etc., totaling no less than 27 tests. ★(3) Environmental performance testing: Based on GB 18580-2017 “Formaldehyde Emission Limits in Wood-based Panels and Their Products for Interior Decoration and Renovation”, the formaldehyde emission level is <0.005 mg/m³; also referring to GB 18584-2001 “Limits of Harmful Substances in Wooden Furniture for Interior Decoration and Renovation”, the levels of the four heavy metals are within acceptable limits (mg/kg for soluble lead ≤2.8, cadmium ≤0.1, chromium ≤0.2, mercury: not detected). ★(4) Antibacterial Performance Test: Based on JC/T2039-2010 standard, the test must meet the following criteria: * *Escherichia coli*, *Staphylococcus aureus*, *Klebsiella pneumoniae*, *Salmonella typhimurium*, *Staphylococcus epidermidis*, *Pseudomonas aeruginosa*, *Shigella sonnei*, *Staphylococcus albus*, *Enterococcus faecalis*; *Methicillin-resistant Staphylococcus aureus*, *Listeria monocytogenes*, *C. mutagenesis*, *Streptococcus hemolyticus*, etc., with an antibacterial rate ≥95%.

★(5) Antifungal Performance Test: Based on JC/T2039-2010 standard, the test must meet the following criteria: * *Aspergillus niger*, *Aspergillus terreus*, *Chaetomium globosum*, *Penicillium wanensis*, *Penicillium cordiformis*, *Brachystomum buddingum*, etc., with an antifungal level of 0.

★(6) Smoke Toxicity Test: According to GB 8624-2012 “Classification of Combustion Performance of Building Materials and Products” standard, smoke toxicity level t1: ZA3 (reaching the quasi-safe level 3 ZA3).

★(7) Anti-aging Test: According to GB/T24508-2020 standard: no cracking, no blistering, no powdering after 48 hours.

Bidders must provide authorization certificates issued by the manufacturer, and only one company can be authorized by the same manufacturer; bidders must provide a copy of the manufacturer’s 2021 or later version of the test report with CMA or CNAS mark and QR code anti-counterfeiting identification, and must indicate the name and number of this tender and affix the manufacturer’s official seal.

3. Backpack Dust: Overall dimensions 400*250*100mm, made of environmentally friendly ABS plastic, injection molded in one piece, with reinforcing ribs on the bottom and top to prevent deformation and bending. Rounded corners for a simple and elegant appearance. A screw hole is injection-molded at the center of the front end of the backpack compartment, which is then fixed to the central crossbeam with screws. This design allows for easy disassembly and assembly. A recessed circular groove in the middle provides a convenient storage and placement of laboratory stools, contributing to a neater and more aesthetically pleasing overall laboratory appearance.

4. The sides utilize a three-section high-strength aluminum alloy structure. Overall dimensions: 560*760mm, with the upper support measuring 562*124*46mm and the lower support measuring 562*122*55mm. The uprights feature a slanted design, with 20mm of embedded upper and lower cast aluminum supports, and a reinforcing support beam at the rear. The upper and lower side supports are made of 3mm thick die-cast aluminum in a single piece. Each part is connected using dedicated positioning components and secured with two 8*25 high-strength hexagonal screws on each side for easy assembly and disassembly. The streamlined design is simple and beautiful, with rounded corners at all points prone to impact. The overall design is aesthetically pleasing, practical, safe, sturdy, and durable. The upper and lower brackets are made of die-cast aluminum, undergoing multiple processes including rough grinding, fine grinding, precision grinding, and polishing to achieve a smooth finish. The metal surface is then coated with high-gloss milky white epoxy resin outdoor powder and cured at high temperature, resulting in strong load-bearing capacity and resistance to acids, alkalis, and corrosion. The upper bracket features a power socket hole with a dedicated metal fixing groove die-cast in the center, designed for use with a standard five-hole socket. The socket’s plastic housing has four built-in slots that can be directly inserted into the upper bracket for fixation, eliminating the need for screws or glue. Each bracket has two 16mm diameter wiring holes, allowing the power socket to be connected to the uprights for easy wiring and cable routing, preventing exposed wires. A plastic protective cover further protects the power socket, ensuring electrical safety. The socket has been tested by an authoritative third-party testing agency and comes with a national mandatory product certification test report. The lower bracket can be fitted with feet to adjust the table height or fixed to the ground via dedicated holes, and comes with decorative ABS foot covers in different colors.

5. The uprights feature a rhomboid octagonal structure, measuring 105*50mm with a thickness of 1.5mm. There are four vertical and four inclined surfaces; the angle between the front vertical surface and the inclined surface is 19 degrees, and the angle between the side vertical surface and the inclined surface is 71 degrees. A groove is provided in the center of the outer surface of the upright for easier and more aesthetically pleasing connection to the central crossbeam. An edge banding strip is added to the groove to conceal screw holes, eliminating visible screw holes on the sides of the table and protecting users from injury from the aluminum edges. Different colors are used to paint the edge banding strips to enrich the overall color scheme of the table.

6. The front, middle, rear, and lower middle crossbeams are all made of high-strength extruded aluminum alloy profiles. Each part is connected using dedicated positioning parts and high-strength hexagonal screws for easy assembly and disassembly. The streamlined design is simple and beautiful. The aluminum surface is treated with epoxy resin outdoor powder electrostatic spraying, ensuring strong load-bearing capacity and resistance to acids, alkalis, and corrosion. The central crossbeam measures 37*28mm and features a unique tear-out design on the aluminum material. After installation, a groove can be torn into the aluminum to house the power cord, maximizing student electrical safety and simplifying wiring. The front and rear crossbeams measure 50*41mm, featuring a semi-circular ergonomic design at the front with an R30 arc angle. The thickness at the mounting screws is 1.7mm, and the rest is 1.2mm. The rear crossbeam has a sliding groove for installing the water-retaining strip, which measures 14*52mm. The lower central crossbeam measures 100*19mm and features a tapered design at both ends to enhance its strength.

7. The back water-retaining strip is integrally extruded using a mold, with different height inserts for different tabletop thicknesses. Appropriately sized aluminum alloy water-retaining blocks are also provided to secure the aluminum alloy table corners and the water-retaining strip. The aluminum alloy water-retaining block is made of one-piece die-cast aluminum alloy, and the surface is electrostatically powder-coated with outdoor epoxy resin.

8. Lower Support Legs: Each end of the lower support leg has a 10mm diameter circular hole. Threads are tapped into the die-cast support, allowing it to be fixed to the ground with expansion screws or used with 50mm diameter adjustable feet. The adjustable feet are made of 12×50 standard screws and high-quality plastic, providing strong load-bearing capacity. The table corners are equipped with ABS foot covers in different decorative colors.

9. The table has been tested by a national authoritative third-party testing institution. The metal surface coating is smooth and uniform, with consistent color, and free from defects such as drips, bumps, wrinkles, and overpainting. The areas in contact with the human body are smooth and burr-free. The table’s mechanical properties have been tested and meet the standard requirements of GB 24820-2009 “General Technical Conditions for Laboratory Furniture”. The aluminum alloy profiles used in the table have been tested and their dimensional deviations, mechanical properties, and chemical composition all meet the standard requirements of GB/T 5237.4-2017 “Aluminum Alloy Building Profiles”. The aluminum material has a Vickers hardness of 77, passes the hydrochloric acid resistance test, and achieves a solvent resistance of 4. An inspection report issued by a provincial or higher-level testing institution is required.

Customization service

HYHOO’s main business is “teaching furniture”, “medical care furniture” and “office furniture”. The products cover “apartment beds, desks and chairs, steel cabinets, auditorium chairs, event stands, waiting chairs, public seats , dining tables and chairs, libraries, laboratories, army barracks, medical furniture, office furniture” and other product series, with more than 1,000 product varieties.

Products are widely used in government agencies, troops, public security, public institutions, institutions of higher learning, financial institutions, medical care and other units.

Certificate of Honor

Related products

Products

Talk to your HYHOO furniture manufacturing expert

With a vertically integrated operation spanning R&D, production, sales, and installation, we deliver holistic experiences that redefine modern environments.

滚动至顶部

Contact Us Now

If you would like to have a question then get in touch today, we are ready to assist 24/7.
We welcome your cooperation and we will develop with you.